Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub
Blog Article
We have discovered this article pertaining to A Step-by-Step Guide to Installing a Bathtub down the page on the internet and think it made perfect sense to talk about it with you on this page.
Setting up a bath tub isn't specifically brain surgery, however it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably challenging job. If the old tub is readily accessible, the task can relocate immediately; if you have to open a wall surface to eliminate the old bathtub as well as position the brand-new tub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require a helper to leave the old bathtub as well as embeded in the new one. Make certain you have qualified on your own for the job as well as fit attempting it. Instead of working with a specialist to take control of a halfway-completed project, it is much better to take into consideration employing one before you begin. Possibilities are you might require a professional plumber to make tube connections.
This article will help you install a new bathtub in your washroom if you have actually currently gotten a brand-new bathtub and don't require to change the plan of your previous water supply pipelines.
Your tools and also material list should make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your setup, after that the first thing you must do is detach the supply of water. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The procedure of eliminating the existing faucets can be quite problematic due to the limited accessibility that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will come from the pipelines. Once the supply pipelines have been removed, use the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning throughout this procedure. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any type of old sealing substance.
Before going on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the other end offers a connection to the existing supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the mounting hole in the bath/basin making sure that the washing machines are in place in between the tap as well as the sink. Safeguard the tap in position with the maker offered backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous kind must be linked to the tap ends initially, tightening just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have been attached.
Mounting the Tub
Using both wooden boards under its feet, position the tub in the called for setting. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub up until the spirit level reads degree.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the appropriate supply pipeline by making a compression join; after that do the very same for the various other faucet.
Activate the water system as well as examine all joints and also brand-new pipework for leakages as well as tighten them if essential. Load the bath tub as well as likewise inspect the overflow outlet and the regular electrical outlet for leakages.
Lastly, fix the bath paneling as defined in the maker's instruction manual. Tiling and sealing around the bath tub must wait until the bath tub has been made use of at the very least once as this will certainly settle it right into its final placement.
Getting ready for the Installation
To start with, the supporting structure supplied with the bath needs to be fitted (if needed) according to the supplier's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also sensible to fit a supporting plate under the faucets unit to prevent stress on the tub.
Fit the flexible faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its final setting.
Tiling Around the Bath tub
In the location where the bathroom meets the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to fracture a rigid seal, triggering the water to pass through the wall surface in between the bathroom as well as the tiling, leading to problems with dampness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealers to assimilate your fixtures and installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the tub with water before sealing, to permit the motion experienced when the bathtub is in usage. The sealer can break rather early if you do not think about this movement prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily offered on the marketplace. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I hope you liked our section on Tools You Need to Install a New Bathtub . Thanks a ton for taking time to read our article. Sharing is caring. Helping others is fun. I treasure reading our article about How to Install a Bathtub.
Request Your Service Report this page